CompTIA 220-1201 - CompTIA A+ Core 1 Exam (2026)

The correct answer is B. Change the fuser temperature .

According to CompTIA A+ Core 1 220-1201 objectives under Printers:

A laser printer fuses toner onto paper using heat and pressure. Thicker paper often requires a higher fuser temperature to properly adhere the toner.

If the output smudges on thick paper but prints fine on standard paper, adjusting the fuser temperature is the first step before performing more invasive maintenance or replacing parts.

Why the other options are incorrect:

A. Install a maintenance kit: Typically includes rollers, belts, and other parts; this is not the first action if the issue is temperature-related.

C. Clean the transfer roller: Cleaning may improve print quality, but smudging on thick paper usually relates to insufficient fusing heat.

D. Install an OEM toner cartridge: The issue is unlikely to be caused by non-OEM toner if standard paper prints correctly.

The correct answer is A. 2.4GHz .

In the CompTIA A+ Core 1 220-1201 networking objectives, wireless networking technologies include frequency bands such as 2.4GHz, 5GHz, and 6GHz , along with related concepts like channels, regulations, channel selection, Bluetooth, 802.11 standards, NFC, and RFID.

The 2.4GHz band supports the most devices because it is the oldest and most widely adopted Wi-Fi frequency listed. Many legacy devices, including older laptops, printers, IoT devices, smart home devices, and wireless peripherals, still rely on 2.4GHz. It also has better range and wall penetration than higher-frequency bands, although it is usually more crowded and slower.

Why the other options are incorrect:

B. 5GHz

5GHz is newer than 2.4GHz and generally provides faster speeds with less interference, but it does not support as many older legacy devices.

C. 6GHz

6GHz is the newest Wi-Fi frequency option used with newer Wi-Fi standards, so it has the least legacy device support among the Wi-Fi frequency choices.

D. NFC

NFC is a short-range communication technology, not a Wi-Fi frequency band. It is used for close-proximity functions such as tap-to-pay, pairing, and access cards, so it is not the best answer.

Final Answer: A. 2.4GHz

The correct answer is A. Loopback plug .

According to CompTIA A+ Core 1 220-1201 objectives under Networking:

A loopback plug is used to test a network interface card (NIC) port by sending a signal out of the port and back into the same port, verifying that the NIC can send and receive data properly .

This is a common diagnostic tool when troubleshooting network connectivity issues on individual devices.

Why the other options are incorrect:

B. Toner probe: Used for tracing and locating cables, not for testing NIC ports.

C. Cable tester: Checks the integrity of network cables but does not verify NIC send/receive functionality.

D. Network tap: Passively monitors network traffic but does not test the NIC port itself.

To ensure seamless connectivity during (and after) migrating an application server, the best DNS approach in CompTIA A+ Core 1 (220-1201) terms is to use a CNAME (Canonical Name) record, which creates an alias from one hostname to another. Instead of users connecting directly to a server’s changing hostname, they connect to a consistent service name (for example, app.company.com). That name can be configured as a CNAME pointing to the current host (such as server1.company.com). When the application is moved to a new server, the technician updates what the alias ultimately resolves to (or updates the target host’s A/AAAA record), and clients continue using the same familiar application URL/name—minimizing disruption and avoiding the need to reconfigure endpoints across devices.

The other record types are not designed for this purpose. TXT records store text-based information (often verification or policy data). SPF and DKIM are email authentication-related mechanisms (typically implemented via TXT records) used to validate authorized mail senders and message integrity—not application server migration. Because the goal is maintaining a stable name for a service while the underlying host changes, CNAME is the correct record type.

The correct answer is B. Near-field communication (NFC) .

According to the CompTIA A+ Core 1 220-1201 objectives under Mobile Devices and Security:

NFC is commonly used for secure access control. Many organizations implement NFC-enabled ID badges or mobile devices to unlock doors, gates, or secure areas.

The mobile device communicates over a very short range (a few centimeters) with a reader to authenticate the user.

Why the other options are incorrect:

A. Hotspot: Provides internet access, not physical building access.

C. Infrared scanner: While used in some legacy devices, it is not commonly implemented for secure mobile access.

D. Geolocation: Can provide location awareness but does not grant direct access to secure physical spaces.

A switch is the network device that controls and forwards traffic primarily based on MAC addresses. In CompTIA A+ Core 1 networking, a switch operates at Layer 2 (Data Link) of the OSI model. When devices communicate on an Ethernet LAN, the switch learns the source MAC addresses from incoming frames and stores them in a MAC address table (CAM table) along with the port where each device is connected. After learning, the switch uses the destination MAC address in each Ethernet frame to decide which specific port should receive the traffic, which reduces unnecessary transmissions and improves overall network efficiency compared to a hub. If the destination MAC is unknown, the switch will flood the frame out other ports (except the one it came in on) until it learns the correct location.

A router makes forwarding decisions using IP addresses at Layer 3, not MAC-based switching decisions. A PoE injector only supplies electrical power over Ethernet and does not manage traffic forwarding. A firewall filters traffic based on rules (IP, ports, protocols, and sometimes application/state), but the classic CompTIA A+ answer for MAC-based traffic control on a LAN is a switch.

NTP (Network Time Protocol) is specifically designed to synchronize the clocks of networked computers and devices automatically.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.6 – Network services and protocols:

“NTP is used to automatically synchronize system clocks on network devices, ensuring all systems have accurate time.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Networking Protocols

CompTIA Exam Objectives 220-1101, Domain 2.6

============

Virtualization is the most suitable solution for maintaining a legacy application that is currently running on multiple physical servers. According to CompTIA Core 1 (220-1201) virtualization concepts, virtualization allows physical servers to be consolidated into virtual machines (VMs) that run on a single or reduced number of physical hosts while preserving the original operating systems and application environments.

Legacy applications often rely on older operating systems, specific hardware configurations, or outdated dependencies. Virtualization enables the organization to encapsulate the legacy environment, reducing hardware dependency and simplifying maintenance until the application can be fully retired. This approach also lowers power consumption, hardware costs, and physical space requirements while improving manageability and backup options.

A SAN (Storage Area Network) provides shared storage but does not address application hosting or server consolidation. FaaS (Function as a Service) is a cloud-native, event-driven computing model that requires application redesign and is unsuitable for legacy systems. A configuration management platform is used to manage and automate system configurations but does not replace physical servers or host applications.

CompTIA highlights virtualization as a key strategy for supporting legacy systems, improving flexibility, and extending the lifespan of applications during transition periods.

The correct answer is D. Data is being throttled .

Data throttling refers to the intentional slowing down of internet speeds by a mobile carrier after a user reaches a certain data usage limit or during network congestion. In this scenario, the employee can still successfully upload files, but the speed has decreased compared to before—this is a classic symptom of throttling.

Why the other options are incorrect:

A. Wireless is turned off

If wireless were turned off, the employee would not be able to upload anything at all. The question clearly states that uploads are still successful.

B. 5G is disabled

Disabling 5G could reduce speeds slightly if the device falls back to 4G/LTE, but it would not typically cause a significant or noticeable degradation unless compared under ideal conditions. It is not the most likely cause.

C. Roaming is turned on

Roaming allows connectivity outside the home network. While it may incur additional charges, it does not inherently cause significant speed reduction in most modern networks. It is less likely than throttling.

Exam Tip (Core 1 220-1201):

Slow but working connection → Think throttling or congestion

No connection → Think disabled wireless or network issues

Final Answer: D. Data is being throttled

The correct answers are E. NFC and F. Location services .

According to CompTIA A+ Core 1 220-1201 objectives under Mobile Devices and Security:

NFC (Near-Field Communication) : Enables the device to communicate with contactless payment terminals, which is essential for detecting nearby stores that accept contactless payments.

Location services : Allows the application to determine the user’s geographic location so it can provide notifications only when the user is near a participating store.

Why the other options are incorrect:

A. MDM (Mobile Device Management): Manages device policies but does not enable location-based notifications or contactless payments.

B. Contact syncing: Synchronizes contacts; unrelated to payment notifications.

C. Bluetooth: Can be used for some proximity services, but NFC is required for contactless payment detection.

D. Hotspot: Provides internet access; not required for proximity detection in this context.