Winter Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: ecus65

Cisco 350-601 - Implementing Cisco Data Center Core Technologies (350-601 DCCOR)

Page: 5 / 11
Total 347 questions

Refer to the exhibit.

An engineer must enable interlace Eth1/2 when the interface Ethi/1 is shut down using EEM on a Cisco Nexus 9000 Series Switch. Which command set accomplishes this goal?

A.

event syslog pattern Down_lnterface

event manager applet "Interface Ethernetl/2. changed state to administratively down"

B.

event syslog pattern Down_lnteriace

event manager applet "Interface Ethemetl/1, changed state to administratively down"

C.

event manager applet Down_lnterface

event syslog pattern "Interface Ethernet 1 '1. changed state to administratively down"

D.

event manager applet Down interface

event syslog pattern "Interface Ethernet 1/2, changed state to administratively down"

In a data center based on Cisco Nexus 9000 Series Switches, all endpoints support explicit congestion notifications How does the Nexus switch respond when the ECN-enabled queue reaches the maximum WRED threshold?

A.

All the outgoing packets are marked.

B.

Low-priority incoming packets are dropped

C.

A congestion notification packet is sent to the sender

D.

A pause frame is sent to the source.

A network engineer must roll back a configuration change made on a Cisco Nexus 9300 Series Switch. Before the change, the network engineer created a checkpoint named pre-config. The rollback abort if any errors occur. Which command must be used to accomplish these objectives?

A.

Option A

B.

Option B

C.

Option C

D.

Option D

What are two capabilities of the Cisco Network Assurance

Engine? (Choose two.)

A.

It validates that devices comply with network security policies.

B.

It predicts the network load on a data center.

C.

It verifies the speed of network packet flows by using telemetry.

D.

It predicts the impact of changes to the network.

E.

It ensures that network performance meets an SLA.

Refer to the exhibit.

An engineer must activate the port-security database on a Cisco MDS 9000 Series Switch for VSAN 100, but receives the error shown. Which command completes the

configuration?

A.

port-security vsan 100 database active

B.

port-security activate vsan 100 force

C.

port-security enabled mode vsan 100

D.

port-security config-enable vsan 100

An engineer musí Implement fabric binding on the Cisco MDS 9000 Series Switch lor only VSAN 110. Both WWNs must be part of domain 110. The configuration for the active VSAN must be compared to the active configuration after the deployment Is completed. Drag and drop the code snippets from the bottom onto the blanks In the code on the top to complete the configuration. Not all code snippets are used

What is a disadvantage of deploying network-attached storage (NAS) versus Fibre Channel for storage?

A.

NAS lacks the scalability and performance of Fibre Channel.

B.

NAS centralizes storage devices which makes them easier to manage

C.

NAS is more complex and expensive to implement

D.

NAS operates independently of an organization's operating system

Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development. Which attribute must be used to assign me servers to different microsegments?

A.

VM name

B.

data center

C.

VMM domain

D.

IP address

Which data interchange format is presented in this output?

A.

XML

B.

YAML

C.

JSON

D.

CSS

Refer to the exhibit An engineer must build the VXLAN for a new customer

BGP is configured for Layer 3 connectivity and is confirmed to work as

expected The deployment must meet these entena:

•All VNI IDs must contain the VLAN that they represent

•Multicast must be used to transport ARP messages between the pods

Drag and drop the code snippets from the bottom onto the boxes in the code to complete the remaining Layer 2 connectivity.

Not all code snippets are used.