CWNP CWNA-109 - Certified Wireless Network Administrator

In the 2.4 GHz frequency band used for 802.11 wireless networks, the channel bandwidth is typically 20 MHz, but the actual frequency spread of each channel is about 22 MHz due to the modulation techniques used. This spread causes overlap between adjacent channels, which can lead to interference and degrade network performance. To avoid this, it's essential to use non-overlapping channels.

The three non-overlapping channels in the 2.4 GHz band are 1, 6, and 11. Each of these channels is spaced sufficiently apart to avoid interference with each other:

Channel 1: Centered at 2.412 GHz.

Channel 6: Centered at 2.437 GHz.

Channel 11: Centered at 2.462 GHz.

Given the options provided, option C (1 and 5) is the closest to a pair of non-overlapping channels, although in practice, channel 5 would still cause some interference with channel 1 due to the 22 MHz spread. The ideal choice for non-overlapping channels would be any two channels among 1, 6, and 11, but this is not an option provided. Therefore, within the given options, 1 and 5 are the best choice, understanding that in a real-world scenario, 1 and 6 or 6 and 11 would be preferred to avoid overlap.

Airtime Utilization is a per-channel statistic that defines what percentage of the channel is currently being used, and what percentage is therefore free. Airtime usage can come from: Data traffic to and from client devices. Interference from WiFi and non-WiFi sources. Management overhead from APs and client devices. https://wyebot.com/2019/06/06/understanding-airtime-utilization/

When performing a post-deployment validation survey for voice over Wi-Fi (VoWiFi), an action that must be performed is Application analysis with an active phone call on a VoWiFi handset. Application analysis is a method of testing the performance of a specific application over the WLAN by measuring parameters such as throughput, latency, jitter, packet loss, MOS score, and R-value. Application analysis with an active phone call on a VoWiFi handset can help to evaluate the quality of service (QoS) and user experience of VoWiFi calls over the WLAN. It can also help to identify any issues or bottlenecks that may affect VoWiFi calls such as interference, roaming delays, or insufficient coverage. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 549; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 519.

Weak signal strength is the likely cause of the low data rate issue for the client that has a signal strength of -84 dBm and a noise floor of -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. Signal strength is the measure of how strong the RF signal is at the receiver. Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the traffic. The higher the signal strength, the better the signal quality and the higher the data rate. The lower the signal strength, the worse the signal quality and the lower the data rate.

The data rate of an 802.11ac connection depends on several factors, such as channel bandwidth, modulation and coding scheme (MCS), spatial streams, guard interval, and beamforming. However, these factors are also influenced by the signal strength, as they require a certain signal-to-noise ratio (SNR) to operate properly. SNR is the ratio of the signal strength to the noise floor, which is the measure of the background noise or interference in the RF environment. The higher the SNR, the more robust and efficient the communication. The lower the SNR, the more prone and vulnerable to errors and retries.

According to the CWNA Official Study Guide , Table 3.7, page 112, an 802.11ac connection with a channel bandwidth of 80 MHz, an MCS of 9, two spatial streams, a short guard interval, and no beamforming can achieve a maximum data rate of 867 Mbps. However, this data rate requires a minimum SNR of 30 dB to maintain a sufficient signal quality. If the signal strength is -84 dBm and the noise floor is -96 dBm, then the SNR is only 12 dB (-84 dBm - (-96 dBm) = 12 dB), which is far below the required SNR for this data rate. Therefore, the data rate will drop significantly to match the lower SNR and signal quality.

To solve this problem, the signal strength should be increased to improve the SNR and data rate. This can be done by adjusting the output power or channel assignment of the AP or client, relocating or reorienting some APs or antennas to reduce attenuation or interference, updating or replacing some faulty or outdated hardware or software components, etc. References: , Chapter 3, page 112; , Section 3.2

What should be inspected to verify proper configuration is DNS. DNS stands for Domain Name System and is a service that resolves hostnames to IP addresses. In a controller-based AP deployment, DNS can be used to help the AP locate the controller by using a predefined hostname such as CISCO-CAPWAP-CONTROLLER or aruba-master. The AP sends a DNS query for this hostname and receives an IP address of the controller as a response. Therefore, if DNS is not configured properly or if there is no DNS entry for the controller hostname, the AP may not be able to locate the controller. NTP, BOOTP, and AP hosts file are not relevant for this scenario. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 374; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 364.

https://www.wlanmall.com/what-is-a-wireless-bridge/

Wireless bridging is a WLAN technology role that allows two or more networks to be connected wirelessly over a distance. A wireless bridge consists of two or more APs that are configured to operate in bridge mode and use directional antennas to establish a point-to-point or point-to-multipoint link. Wireless bridging can support high data rates and is suitable for scenarios where running cables is impractical or expensive. To create a wireless link between two buildings on a single campus that supports at least 150 Mbps data rates, wireless bridging is an appropriate solution678. References: CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 271; CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 265; Wi-Fi Wireless Bridging Explained.

Based on the information given, what can be determined as certainly true about this AP is that it has 4 radio chains. A radio chain is a hardware component that consists of an antenna, a radio frequency (RF) amplifier, and a transceiver. The number of radio chains indicates how many spatial streams an AP can transmit or receive simultaneously using Multiple Input Multiple Output (MIMO) technology. The notation x:y:z in an AP specification denotes the number of radio chains (x), the number of spatial streams (y), and the number of spatial streams per band (z). Therefore, a tri-band, 4x4:4, Wi-Fi 6, 802.11ax AP has four radio chains in each of its three bands (2.4 GHz, low 5 GHz, and high 5 GHz). It also supports four spatial streams in total and four spatial streams per band. It cannot be determined as certainly true that it supports four channels in each band, UL-MU-MIMO, or uses a modified OpenWRT firmware based on the information given. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 223; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 213.

 iPerf is an open source tool that is designed to perform a throughput test on the WLAN. iPerf is a cross-platform command-line tool that can measure the bandwidth and quality of network links by generating TCP or UDP traffic between two endpoints. iPerf can run as either a server or a client mode, depending on whether it receives or sends traffic. iPerf can also report various metrics of network performance, such as throughput, jitter, packet loss, delay, and TCP window size. To perform a throughput test on the WLAN using iPerf, one device needs to run iPerf in server mode and another device needs to run iPerf in client mode. The devices need to be connected to the same WLAN network and have their IP addresses configured properly. The device running iPerf in client mode needs to specify the IP address of the device running iPerf in server mode as well as other parameters such as protocol, port number, duration, interval, bandwidth limit, packet size, etc. The device running iPerf in server mode will listen for incoming connections from the client device and send back acknowledgments or responses depending on the protocol used. The device running iPerf in client mode will send traffic to the server device according to the specified parameters and measure the network performance. The device running iPerf in client mode will display the results of the throughput test at the end of the test or at regular intervals during the test. The results can show the average, minimum, maximum, and instantaneous throughput of the network link, as well as other metrics such as jitter, packet loss, delay, and TCP window size. References: 1, Chapter 7, page 287; 2, Section 4.3

WPA2 (Wi-Fi Protected Access 2) is a security certification program developed by the Wi-Fi Alliance to secure wireless computer networks. It is important to understand the following:

WPA2 and the 802.11 Standard: While WPA2 is based on elements of the 802.11i amendment to the 802.11 standard, it is not itself a standard but rather a certification to ensure devices comply with certain security criteria, including the correct implementation of CCMP (Counter Mode Cipher Block Chaining Message Authentication Code Protocol) and AES (Advanced Encryption Standard).

CCMP/AES Implementation: WPA2 enhances the security of wireless networks by using CCMP for encryption, which is based on AES, a robust encryption algorithm. This represents a significant security improvement over WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected Access) that used TKIP (Temporal Key Integrity Protocol).

WPA vs. WPA2: WPA was the interim security enhancement over WEP, utilizing TKIP for encryption. WPA2, however, moved to the more secure AES-based encryption method. Contrary to option C, WPA2 does not enhance security by using TKIP; it uses CCMP/AES.

Therefore, option B correctly describes WPA2 as a certification program ensuring devices properly implement the more secure CCMP/AES encryption methods.

Channel 144 is a new channel that was added to the 5 GHz band by the 802.11ac amendment, which defines the VHT (Very High Throughput) PHY for WLANs. Channel 144 has a center frequency of 5720 MHz and a bandwidth of 20 MHz. It can also be combined with adjacent channels to form wider channels of 40 MHz, 80 MHz, or 160 MHz. Channel 144 is available in some regions, such as North America and Europe, but not in others, such as Japan and China . References: [CWNA-109 Study Guide], Chapter 3: Antennas and Accessories, page 121; [CWNA-109 Study Guide], Chapter 3: Antennas and Accessories, page 115; [Wikipedia], List of WLAN channels.