Hitachi HQT-4420 - Hitachi Vantara Qualified Professional - Content Platform Installation

The HCP back-end network is specifically designed to handle internal cluster traffic such as inter-node communication. This traffic type is critical for maintaining cluster synchronization, managing metadata, balancing loads, and ensuring consistent data storage and retrieval across the nodes in the cluster. Other types of traffic, like BMC access (A), tenant management console access (B), and replication traffic (D), typically occur over separate management or front-end networks. The "HCP Network Configuration and Management Guide" provides detailedinformation on network segmentation and the roles of different network types in an HCP environment.

When installing an HCP G10 with attached storage using a VSP G1000, which is also used by several other applications, it is crucial to configure the system properly to allow shared storage use. The installation program for HCP G10 has a prompt that allows you to specify that shared storage is being used. By selecting this option, the system is informed that the VSP G1000 storage resources are shared among multiple applications, allowing for proper configuration and optimization to prevent any disruptions or conflicts. This ensures that HCP uses the storage without impacting other applications relying on the same storage system.

Hitachi Vantara Content Platform Installation References:

When setting up an HCP G10, especially in environments with shared storage configurations like the VSP G1000, the installation wizard will prompt for shared storage settings to ensure compatibility and optimal configuration.

If the pre-upgrade check procedure fails due to insufficient capacity on node 103 to perform the upgrade, the service procedure to run isFree Space On Nodes. This procedure helps to identify and clear unnecessary files or redistribute data, freeing up the required capacity on the node to proceed with the upgrade.

Hitachi Vantara Content Platform Installation References:

The "Free Space On Nodes" procedure is specifically designed to manage and optimize storage capacity across HCP nodes, ensuring that upgrades and other operations have adequate space to execute successfully.

For theHCP S11, the base configuration of theCompute Storage (CS) trayconsists of the following components:

2x Intel Servers: The tray is equipped with two Intel-based servers, which handle compute tasks and manage the storage operations.

6x SSD disks: These SSDs are used for fast data access and caching, significantly improving the overall performance of the system by speeding up read and write operations.

42x HDD disks: The 42 hard disk drives (HDDs) provide the bulk of the storage capacity for the system, which is designed for large-scale, long-term storage. HDDs are optimized for durability and cost-effective storage of large data sets.

This configuration ensures a balance between compute power, high-speed storage, and large capacity, making the HCP S11 suitable for environments that require high performance and significant storage scalability.

References:

Hitachi Vantara HCP S11 Installation Guide

Hitachi Vantara HCP S11 System Architecture Documentation

Top of Form

Bottom of Form

When installing an HCP G10 and setting up front-end connectivity, two critical actions must be performed on each node:

Set the BMC IP Address (A):The Baseboard Management Controller (BMC) IP address must be set to allow for remote management and monitoring of each node. This is crucial for out-of-band management, especially in large data center environments where physical access to servers may be limited. Configuring the BMC IP address is typically done during the initial setup of the operating system on the HCP node.

Set the Front-End IP Address (C):The front-end IP address, which is used for client network traffic, must be configured as provided by the customer. This IP address allows each node to communicate with the client network, and it is a key part of the configuration during OS installation.

These configurations are detailed in the "HCP G10 Network Configuration Guide" and the "HCP G10 Installation and Configuration Manual," which provide step-by-step procedures for setting up both the BMC and front-end IP addresses.

When performing an online upgrade of an HCP G10 and the upgrade fails, theArc-deploy logsare the relevant logs available to assist with troubleshooting. These logs contain detailed information about the deployment and upgrade processes, including errors or issues encountered during the upgrade. Accessing these logs allows administrators to diagnose the failure and take corrective actions.

Hitachi Vantara Content Platform Installation References:

The Arc-deploy logs are essential for understanding the sequence of events and identifying the exact step or component that caused the failure during an online upgrade of the HCP G10.

To upload a software update package to an HCP S10, an SFTP (Secure File Transfer Protocol) connection is used. SFTP provides a secure way to transfer files between the administrator's machine and the HCP S10 system. This method ensures that the package is securely transmitted and prevents unauthorized access during the upload process.

Hitachi Vantara Content Platform Installation References:

The HCP S10 system requires secure methods for software updates, and SFTP is the recommended protocol for its ability to provide encryption and secure file transfer.

After adding new nodes to an HCP G10 system, the following actions should be performed:

Upgrade the new nodes' software: Ensuring that the newly added nodes are running the same software version as the existing nodes is essential for compatibility and stability within the cluster.

Run the capacity balancing service: This service redistributes data across all nodes in the cluster to ensure balanced storage utilization and optimal performance, especially after the addition of new nodes.

Hitachi Vantara Content Platform Installation References:

These steps are necessary to maintain consistency, stability, and efficient use of resources within the HCP system after scaling up by adding new nodes.

When performing a six-drive upgrade on an HCP G10 with local storage:

RAID level and Virtual Disks will be created automatically (A):This is correct. The system automatically handles the RAID configuration and creation of virtual disks to ensure that the new drives are correctly integrated into the existing storage structure.

The node is online during this procedure (C):This is also correct. The upgrade can be performed while the node remains online, minimizing disruption to the system's operation and ensuring continuous availability. These procedures are documented in the "HCP G10 Maintenance and Upgrade Guide," which outlines the steps for online upgrades and automatic RAID configuration.