RedHat RH302 - RHCE (Redhat Certified Engineer)

In Network problem think to check:

IP Configuration: use ifconfig command either IP is assigned to interface or not?

Default Gateway is set or not?

Hostname is set or not?

Routing problem is there?

Device Driver Module is loaded or not?

Device is activated or not?

Check In this way:

use ifconfig command and identify which IP is assigned or not.

cat /etc/sysconfig/networkWhat, What is written here. Actually here are these parameters.

NETWORKING=yes or no

GATEWAY=x.x.x.x

HOSTNAME=?

NISDOMAIN=?

Correct the file

Use netconfig command

Either Select Automatically from DHCP or assign the static IP

Use service network restart or start command

Now try to ping it will work.

Do the following steps as:

1.rpm –ivhftp://server1/example.com/pub/updates/zsh-*

or

1.Login to ftp server : ftpftp://server1.example.comusing anonymous user.

2.Change the directory: cd pub and cd updates

3.Download the package: mget zsh-*

4.Quit from the ftp prompt : bye

5.Install the package

6.rpm -ivh zsh-*

7.Verify Either package installed or not : rpm -q zsh

Do the following steps as:

1. /proc is the virtual filesystem, we use /proc to modify the kernel parameters at running time.

# echo “1” >/proc/sys/net/ipv4/ip_forward

2. /etc/sysctl.confwhen System Reboot on next time, /etc/rc.d/rc.sysinit scripts reads the file /etc/sysctl.conf. To enable the IP forwarding on next reboot also you need to set the parameter.

net.ipv4.ip_forward=1

Here 0 means disable, 1 means enable.

Do the following steps as:

hostname station?.example.comThis will set the host name only for current session. To set hostname permanently.

vi /etc/sysconfig/network

HOSTNAME=station?.example.com

service network restart

Do the following steps as:

1.First check the size of Logical Volume: lvdisplay /dev/vo/myvol

2.Increase the Size of Logical Volume: lvextend -L+121M /dev/vo/myvol

3.Make Available the size on online: ext2online /dev/vo/myvol

4.Verify the Size of Logical Volume: lvdisplay /dev/vo/myvol

5.Verify that the size comes in online or not: df -h

We can extend the size of logical Volume using the lvextend command. As well as to decrease the size of Logical Volume, use the lvresize command. In LVM v2 we can extend the size of Logical Volume without unmount as well as we can bring the size of Logical Volume on online using ext2online command.

To understand the role of a boot loader, take a step back from Linux. When you boot your computer, the BIOS starts by detecting basic hardware, including your hard drives. Once it's done, it looks for the boot loader on the Master Boot Record of the first available disk. If you're working with an older PC, the BIOS can't find your boot loader unless it's located within the first 1,024 cylinders of the hard disk.

Newer BIOSes overcome this problem with Logical Block Addressing, which is also known as LBA mode. LBA mode reads 'logical' values for the cylinder, head, and sector, which allows the BIOS to 'see' a larger disk drive.

If you have multiple hard drives, there is one more caveat. If your drives are IDE hard drives, the /boot directory must be on a hard drive attached to the primary IDE controller. If your drives are all SCSI hard drives, the /boot directory must be located on a hard drive with SCSI ID 0 or ID 1. If you have a mix of hard drives, the /boot directory must be located on either the first IDE drive or a SCSI drive with ID 0. In other words, this is not an issue on the Red Hat exams unless the computer that you're tested on has more than two hard drives. And I believe that's less likely, as that would increase the cost of the exam.

If you are getting the Kernel panic error, it means it is boot loader related problem. Redhat Enterprise Linux uses the GRUB boot loader. You can pass the kernel parameter from the boot loader as well as you can correct the kernel parameter passing from boot loader from GRUB screen at boot time.

GRUB boot loader configuration file is: /etc/grub.conf

And Correct Configuration is:

default=0

timeout=5

splashimage=(hd0,0)/grub/splash.xpm.gz

hiddenmenu

title Red Hat Enterprise Linux ES (2.6.9-5.EL)

root (hd0,0)

kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

initrd /initrd-2.6.9-5.EL.img

Probably miss-configured the boot loader, so giving this problem. You can pass the correct parameter from GRUB prompt:

Table 3-3:GRUB Editing Commands

Command

Description

b

Boot the currently listed operating system

d

Delete the current line

e

Edit the current line

o

Create an empty line underneath the current line

O

Create an empty line above the current line

If you know all parameters and sequence of the boot loader you can enter in command prompt also.

Press c on GRUB screen.

Grub>root (hd0,0)

grub>kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

grub>initrd /initrd-2.6.9-5.EL.img

grub>boot

Do the following steps as:

Use fdisk /dev/hdaTo create new partition.

Type nFor New partitions

It will ask for Logical or Primary Partitions. Press l for logical.

It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

Type the Size: +100MYou can Specify either Last cylinder of Size here.

Press P to verify the partitions lists and remember the partitions name.

Press w to write on partitions table.

Either Reboot or use partprobe command.

Use mkfs –t ext3 /dev/hda? Where ? is your partition number

Or

mke2fs –j /dev/hda? To create ext3 filesystem.

mkdir /mnt/neo

vi /etc/fstab

Write:

/dev/hda?/mnt/neoext3defaults1 2

Verify by mounting on current Sessions also:

mount /dev/hda? /mnt/neo

Do the following steps as:

Use netconfig command

Enter the IP Address as given station number by your examiner: example: 172.24.0.1

Enter Subnet Mask

Enter Default Gateway and primary name server

press on ok

ifdown eth0

ifup eth0

verify using ifconfig

In the lab server is playing the role of router, IP forwarding is enabled. Just set the Correct IP and gateway, you can ping to 172.25.254.254.

#vi /etc/resolv.conf

nameserver 172.24.254.254

# dig server1.example.com

#host server1.example.com

DNS is the Domain Name System, which maintains a database that can help your computer translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As no individual DNS server is large enough to keep a database for the entire Internet, they can refer requests to other DNS servers.

DNS is based on thenameddaemon, which is built on the BIND (Berkeley Internet Name Domain) package developed through the Internet Software Consortium

Users wants to access by name so DNS will interpret the name into ip address. You need to specify the Address if DNS server in each and every client machine. In Redhat Enterprise Linux, you need to specify the DNS server into /etc/resolv.conf file.

After Specifying the DNS server address, you can verify using host, dig and nslookup commands.