Summer Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: ecus65

Cisco 200-301 - Cisco Certified Network Associate

Cisco 200-301 Premium Access     Download Demo    
Page: 10 / 13
Total 1069 questions

Drag and drop the application protocols from the left onto the transport protocols that it uses on the right

Which type of traffic is sent with pure iPsec?

A.

broadcast packets from a switch that is attempting to locate a MAC address at one of several remote sites

B.

multicast traffic from a server at one site to hosts at another location

C.

spanning-tree updates between switches that are at two different sites

D.

unicast messages from a host at a remote site to a server at headquarters

How does a Cisco Unified Wireless network respond to Wi-Fi channel overlap?

A.

It alternates automatically between 2.4 GHz and 5 GHz on adjacent access points

B.

It allows the administrator to assign channels on a per-device or per-interface basis.

C.

It segregates devices from different manufacturers onto different channels.

D.

It analyzes client load and background noise and dynamically assigns a channel.

What is the benefit of configuring PortFast on an interface?

A.

After the cable is connected, the interface uses the fastest speed setting available for that cable type

B.

After the cable is connected, the interface is available faster to send and receive user data

C.

The frames entering the interface are marked with higher priority and then processed faster by a switch.

D.

Real-time voice and video frames entering the interface are processed faster

A wireless administrator has configured a WLAN; however, the clients need access to a less congested 5-GHz network for their voice quality. What action must be taken to meet the requirement?

A.

enable AAA override

B.

enable RX-SOP

C.

enable DTIM

D.

enable Band Select

Which JSON data type is an unordered set of attribute- value pairs?

A.

array

B.

string

C.

object

D.

Boolean

Refer to Exhibit.

An engineer is configuring the NEW York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path. Which two commands must be configured on the New York router so that it can reach the Lo1 interface of the Atlanta router via Washington when the link between New York and Atlanta goes down? (Choose two)

A.

ipv6 router 2000::1/128 2012::1

B.

ipv6 router 2000::1/128 2012::1 5

C.

ipv6 router 2000::1/128 2012::2

D.

ipv6 router 2000::1/128 2023::2 5

E.

ipv6 router 2000::1/128 2023::3 5

Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.

Which 802.11 frame type is indicated by a probe response after a client sends a probe request?

A.

action

B.

management

C.

control

D.

data

Which port type supports the spanning-tree portfast command without additional configuration?

A.

access ports

B.

Layer 3 main Interfaces

C.

Layer 3 suninterfaces

D.

trunk ports

What is the primary different between AAA authentication and authorization?

A.

Authentication verifies a username and password, and authorization handles the communication between the authentication agent and the user database.

B.

Authentication identifies a user who is attempting to access a system, and authorization validates the users password

C.

Authentication identifies and verifies a user who is attempting to access a system, and authorization controls the tasks the user can perform.

D.

Authentication controls the system processes a user can access and authorization logs the activities the user initiates

A packet is destined for 10.10.1.22. Which static route does the router choose to forward the packet?

A.

ip route 10.10.1.0 255.255.255.240 10.10.255.1

B.

ip route 10.10.1.16 255.255.255.252 10.10.255.1

C.

ip route 10.10.1.20 255.255.255.252 10.10.255.1

D.

ip route 10.10.1.20 255.255.255.254 10.10.255.1

Refer to the exhibit.

What is the effect of this configuration?

A.

The switch port interface trust state becomes untrusted

B.

The switch port remains administratively down until the interface is connected to another switch

C.

Dynamic ARP inspection is disabled because the ARP ACL is missing

D.

The switch port remains down until it is configured to trust or untrust incoming packets

What are two benefits of network automation? (Choose two)

A.

reduced operational costs

B.

reduced hardware footprint

C.

faster changes with more reliable results

D.

fewer network failures

E.

increased network security

Refer to the exhibit.

The show ip ospf interface command has been executed on R1 How is OSPF configured?

A.

The interface is not participating in OSPF

B.

A point-to-point network type is configured

C.

The default Hello and Dead timers are in use

D.

There are six OSPF neighbors on this interface

All physical cabling is in place. Router R4 and PCI are fully configured and

inaccessible. R4's WAN interfaces use .4 in the last octet for each subnet.

Configurations should ensure that connectivity is established end-to-end.

1 . Configure static routing to ensure RI prefers the path through R2 to

reach only PCI on R4's LAN

2. Configure static routing that ensures traffic sourced from RI will take

an alternate path through R3 to PCI in the event of an outage along

the primary path

3. Configure default routes on RI and R3 to the Internet using the least number of hops

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using

the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Connectivity between three routers has been established, and IP services must be configured jn the order presented to complete the implementation Tasks assigned include configuration of NAT, NTP, DHCP, and SSH services.

1. All traffic sent from R3 to the R1 Loopback address must be configured for NAT on R2. All source addresses must be translated from R3 to the IP address of Ethernet0/0 on R2, while using only a standard access list named NAT To verify, a ping must be successful to the R1 Loopback address sourced from R3. Do not use NVI NAT configuration.

2. Configure R1 as an NTP server and R2 as a client, not as a peer, using the IP address of the R1 Ethernet0/2 interface. Set the clock on the NTP server for midnight on January 1, 2019.

3. Configure R1 as a DHCP server for the network 10.1.3.0/24 in a pool named TEST. Using a single command, exclude addresses 1-10 from the range. Interface Ethernet0/2 on R3 must be issued the IP address of 10.1.3.11 via DHCP.

4. Configure SSH connectivity from R1 to R3, while excluding access via other remote connection protocols. Access for user root and password Cisco must be set on router R3 using RSA and 1024 bits. Verify connectivity using an SSH session from router R1 using a destination address of 10.1.3.11. Do NOT modify console access or line numbers to accomplish this task.

What is a functionality of the control plane in the network?

A.

It exchanges topology information with other routers.

B.

It forwards traffic to the next hop.

C.

It looks up an egress interface in the forwarding information base.

D.

It provides CLI access to the network device.

Configure IPv4 and IPv6 connectivity between two routers. For IPv4, use a /28 network from the 192.168.1.0/24 private range. For IPv6, use the first /64 subnet from the 2001:0db8:aaaa::/48 subnet.

1. Using Ethernet0/1 on routers R1 and R2, configure the next usable/28 from the 192.168.1.0/24 range. The network 192.168.1.0/28 is unavailable.

2. For the IPv4 /28 subnet, router R1 must be configured with the first usable host address.

3. For the IPv4 /28 subnet, router R2 must be configured with the last usable host address.

4. For the IPv6 /64 subnet, configure the routers with the IP addressing provided from the topology.

5. A ping must work between the routers on the IPv4 and IPv6 address ranges.

Connectivity between four routers has been established. IP connectivity must be configured in the order presented to complete the implementation. No dynamic routing protocols are included.

1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.

2. Configure an IPv4 default route on router R2 destined for router R4.

3. Configure an IPv6 default router on router R2 destined for router R4.