CompTIA 220-1201 - CompTIA A+ Core 1 Exam (2026)

When a laptop powers on but the screen is blank, the quickest way to isolate the problem is to connect to an external monitor. This helps determine if the issue is with the laptop display or with the graphics subsystem.

From CompTIA A+ 220-1101 Official Study Guide, Objective 4.1 – Troubleshoot common hardware problems:

“A blank screen on a laptop with power indicators lit should be tested with an external display first to rule out a faulty screen or ribbon cable.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 4: Laptop Display Troubleshooting

CompTIA Exam Objectives 220-1101, Domain 4.1

============

Color gamut refers to the range of colors a display can accurately reproduce. For tasks like graphic design or photo editing, ensuring the screen ' s colors match the printed output is critical. Monitors with wide and accurate color gamuts (e.g., Adobe RGB) are preferred for these applications.

Option B (Pixel density): Incorrect. Pixel density affects image sharpness, not color accuracy.

Option C (Refresh rate): Incorrect. Refresh rate impacts motion smoothness but is unrelated to color matching.

Option D (Resolution): Incorrect. Resolution determines clarity and detail but does not influence color accuracy.

A punchdown tool is specifically used to insert wires into a punchdown block in patch panels, which is typical for Cat 6 and similar cabling. It ensures a secure and correct connection by pushing the wire into a metal groove that slices the insulation.

Laptop display assemblies typically include not only the LCD panel but also the webcam, microphone, display cable, and critically, the Wi-Fi antennas. In most laptops, Wi-Fi antennas are built into the display bezel, because the elevated position allows for stronger wireless signal reception. When replacing the entire display assembly, the antennas must be carefully disconnected and reconnected during reinstallation.

CompTIA A+ emphasizes proper cable routing and antenna reattachment as essential steps in laptop hardware disassembly and reassembly. Failing to reconnect these antennas results in weak or nonfunctional wireless connectivity, even though the display replacement itself may be successful.

Heat sinks and CPU fans are located on the motherboard and are unrelated to display assembly replacement. Resetting BIOS settings is unnecessary unless troubleshooting firmware-related issues, not replacing hardware components like a display. Therefore, the only action that aligns with standard laptop design and CompTIA A+ procedures is ensuring that the wireless antennas are reconnected.

Thus, the correct answer is B.

Shielded Twisted Pair (STP) cabling is specifically designed to protect data transmissions from electromagnetic interference (EMI) and radio frequency interference (RFI). According to CompTIA Core 1 (220-1201) networking cabling objectives, STP cables include an additional shielding layer—either around individual wire pairs or the entire cable—that reduces the impact of external electrical noise.

In environments where network cables are installed near heavy machinery, fluorescent lighting, power cables, or radio transmitters, EMI can cause data corruption, retransmissions, and reduced network performance. STP helps maintain signal integrity in these high-interference environments.

Unshielded Twisted Pair (UTP) relies only on wire twisting to reduce interference and is more susceptible to EMI compared to STP. Thunderbolt and USB are peripheral interface standards, not structured network cabling solutions, and they are not intended for long-distance network installations.

CompTIA emphasizes selecting the appropriate cabling type based on environmental factors, particularly when interference is a concern. For locations with potential EMI, STP is the recommended choice.

A key benefit and defining characteristic of cloud computing in CompTIA A+ Core 1 is on-demand, self-service. This means users or administrators can quickly provision computing resources—such as virtual machines, storage, or applications—without requiring manual intervention from the cloud provider each time. For example, an organization can deploy a new server instance in minutes to support a new project, then scale it down or remove it when no longer needed. This improves agility, speeds up deployment, and supports rapid changes in workload.

Option A is incorrect because cloud services are typically metered (measured) and billed based on usage, which is part of the “measured service” cloud concept. Option B is incorrect because cloud data is often distributed across multiple regions for redundancy and performance; it is not inherently “centralized for all global data.” Option D is incorrect because cloud services generally emphasize broad network access using standard methods and interfaces, not limited access through custom interfaces only. Therefore, on-demand, self-service capabilities best represents a cloud computing benefit.

Quality of Service (QoS) prioritizes VoIP traffic on the network, reducing jitter, latency, and packet loss to improve call quality.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.4 – Network troubleshooting:

“Enabling QoS in the router ensures time-sensitive traffic, like VoIP, receives network priority, reducing dropped or lagging calls.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Network Troubleshooting

CompTIA Exam Objectives 220-1101, Domain 2.4

============

Reasoning: Projectors have air filters that prevent dust from entering the internal components. A clogged filter can cause the projector to overheat, resulting in shutdowns and even strange smells due to overheating components. Cleaning the filter is a standard troubleshooting step when projectors exhibit overheating symptoms.

Why the Other Options Are Incorrect:

A. Replace the bulb:

While a failing bulb may eventually cause issues, it would not typically result in a strange smell or repeated shutdowns after a fixed period. Bulb issues usually manifest as dim or flickering images.

B. Check the projector configuration:

Configuration settings, such as resolution or input options, would not cause overheating or shutdowns. This option does not address the described symptoms.

D. Adjust the gamma settings:

Gamma settings affect display brightness and contrast but have no impact on overheating or strange smells.

Practical Example:

Dust accumulation in projectors is a common issue, especially in environments with poor air circulation. A clogged filter causes restricted airflow, leading to overheating and automatic shutdowns to protect internal components. Cleaning the filter typically resolves this issue.

CompTIA A+ Exam Objective Alignment:

Objective 5.5: Troubleshoot common video, projector, and display issues.

Port flapping refers to a network port continuously going up and down, which can prevent the access point from fully coming online.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.4 – Wired and wireless troubleshooting:

“Repeated loss and restoration of network link is called port flapping and may result in network devices, such as access points, not coming online.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Network Troubleshooting

CompTIA Exam Objectives 220-1101, Domain 2.4

============

Security groups are used to manage access permissions to network resources, ensuring only authorized HR department members can access the shared materials.

Why Not B (Audit logs): Audit logs monitor activity but do not restrict access.

Why Not C (Time-of-day access): Time-of-day access limits when users can access resources but doesn’t specify user permissions.

Why Not D (Print server): A print server manages print jobs but does not control file access.

CompTIA A+ Exam Reference: Core 2 (220-1102), Section 2.5, access control and permissions​.

A CNAME (Canonical Name) record is used in DNS to create an alias that maps one domain name to another canonical domain name. According to CompTIA Core 1 (220-1201) DNS objectives, CNAME records allow multiple hostnames to reference the same IP address indirectly by pointing to a single authoritative domain name.

For example, www.example.com can be configured as a CNAME that points to example.com. When DNS queries are made, the resolver follows the alias until it reaches an A or AAAA record that contains the actual IP address.

An A record maps a hostname directly to an IPv4 address, while an AAAA record maps a hostname to an IPv6 address. A TXT record is used to store arbitrary text data, commonly for verification, email security (SPF, DKIM), or policy information, not for aliasing.

CompTIA stresses that CNAME records are specifically intended for aliasing and name redirection within DNS, making them the correct answer.

CompTIA A+ explains that Secure Boot is a UEFI security feature that prevents unauthorized or malicious bootloaders, rootkits, and unsigned OS loaders from starting during the boot process. Secure Boot verifies digital signatures on the OS and critical boot files before allowing startup, ensuring the system has not been tampered with.

TPM (Option A) provides encryption key storage and is used for BitLocker, but alone does not block malicious bootloaders. HSMs (Option B) are enterprise cryptographic devices, not PC boot protection features. BIOS passwords (Option D) restrict access to configuration but do not protect against malicious boot-level malware.

Windows 11 specifically requires Secure Boot, making it the correct protection mechanism for preventing startup-level malware.

Thus, Secure Boot is the proper choice.

Adocking stationconnects to a laptop’sproprietary port or USB-C/Thunderbolt, providing access tomultiple additional ports(USB, Ethernet, video, audio, etc.). It allows users to transform a laptop into a full desktop workstation.

Option A (NFC adapter):Used for short-range communication, not port expansion.

Option C (Port replicator):Similar to a dock but usually less powerful and often lacks charging or video output.

Option D (USB dongle):Adds a single function (like Wi-Fi or storage), not full port expansion.

CompTIA A+ Core 1 Exam Objective Reference:

Objective 1.4: Given a scenario, configure settings and use cases for laptops and mobile devices.

===========

A valid public IP address must fall outside the private IP address ranges:

10.0.0.0 to 10.255.255.255

172.16.0.0 to 172.31.255.255

192.168.0.0 to 192.168.255.255

66.157.195.20 is outside these ranges, making it a public IP address.

Why Not A, C, D: These IPs fall within private IP address ranges.

CompTIA A+ Exam Reference: Core 1 (220-1201), Section 2.6, IP addressing​.

In CompTIA A+ Core 1 (220-1201) networking and troubleshooting, a common cause of “can’t reach internal resources” while docked is that the laptop is still using the wireless interface (or has a higher interface priority for Wi-Fi) instead of the docking station’s wired Ethernet connection. If the Wi-Fi network is a guest/isolated VLAN, uses different routing, or has stricter access controls, the user may be blocked from reaching department file servers even though an Ethernet cable is physically connected to the dock. Disabling Wi-Fi is a fast, low-risk step that forces the system to use the wired NIC path through the docking station, which typically provides the correct corporate network access, DHCP scope, and routing to internal servers.

Restarting the computer might help in some cases, but it’s less targeted and not the “best next step” when the likely issue is interface selection. Replacing the Ethernet cable is appropriate if link lights are off or the wired connection is clearly down, but the scenario highlights that the dock has a hardwired connection—suggesting the physical layer may be fine. Dock firmware updates are not a first-line fix for basic connectivity/access symptoms.