Summer Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: ecus65

Cisco 300-430 - Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI)

Page: 4 / 7
Total 216 questions

An engineer must control administrative access to the WLC using their Active Directory without being concerned about RBAC after the admin user is authenticated. Which two features does the engineer configure to accomplish this task? (Choose two.)

A.

Device Admin Policy Set

B.

User Access Mode: ReadWrite

C.

ACL

D.

RADIUS server

E.

TACACS server

A wireless administrator receives this information to complete a CMX deployment in high availability by using version 10.6 to gather analytics.

IP address of the primary server

IP address of the secondary server

failover mode to be configured as automatic

root password of the secondary server

email ID for NOC notifications

Enabling high availability fails when these parameters are used. Which action resolves the issue?

A.

Insert the cmxadmin password of the secondary server.

B.

Use IP protocol 4242 for the controller to reach the CMX server.

C.

Place primary and secondary servers in different subnets.

D.

Enable the virtual IP address of the primary server.

When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN ID of 30 to a FlexConnect group named BranchA-FCG?

A.

config flexconnect BranchA-FCG vlan 30 add

B.

config flexconnect BranchA-FCG vlan add 30

C.

config flexconnect group BranchA-FCG vlan 30 add

D.

config flexconnect group BranchA-FCG vlan add 30

Refer to the exhibit.

An engineer must provide a position of rogue APs on a floor map using Cisco PI 3.0, but no rogue AP options are showing on the left-hand navigation menu under Maps. What is the reason for this omission?

A.

An assurance license is not installed.

B.

The controller operational status background task is disabled.

C.

The Show Detected Interferers feature under the AP option is disabled.

D.

Cisco MSE has not been added to Cisco PI.

Which CLI command do you use to shut down the 2.4 GHz radio of the Floor1_AP1 AP on a Cisco 3850 Switch?

A.

ap name Floor1_AP1 dot11 shutdown 24ghz

B.

ap name Floor1_AP1 dot11 5ghz shutdown

C.

ap name Floor1 AP1 dot11 24ghz shutdown

D.

ap name Floor1_AP1 shutdown dot11 24ghz

An engineer is troubleshooting a Cisco CMX high-availability deployment and notices that the primary and backup Cisco CMX servers are both considered primary. Which command must the engineer run on the backup server?

A.

cmxha convert backup

B.

cmxha backup convert

C.

cmxha secondary convert

D.

cmxha convert secondary

An engineer is configuring multicast for wireless for an all-company video meeting on a network using EIGRP and BGP within a single domain from a single source. Which type of multicast routing should be implemented?

A.

Protocol Independent Multicast Dense Mode

B.

Source Specific Multicast

C.

Multicast Source Discovery Protocol

D.

Protocol Independent Multicast Sparse Mode

An engineer is adding APs to an existing VolMLAN to allow for location based services. Which option will the primary change be to the network?

A.

increased transmit power on all APs

B.

moving to a bridging model

C.

AP footprint

D.

cell overlap would decrease

E.

triangulation of devices

What must be configured on ISE version 2.1 BYOD when using Single SSID?

A.

open authentication

B.

802.1x

C.

no authentication

D.

WPA2

Which component must be integrated with Cisco DNA Center to display the location of a client that is experiencing connectivity issues?

A.

Cisco Hyperlocation Module

B.

Wireless Intrusion Prevention System

C.

Cisco Connected Mobile Experiences

D.

Cisco Mobility Services Engine