Weekend Sale Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: xmas50

Acme Packet AP0-001 - Acme Packet Certification Certification Exams Boot camp & Braindump

Page: 3 / 5
Total 140 questions

Which two of the following statements about network interfaces are FALSE?

A.

For each physical interface, you must have at least one network interface with a sub-port-id of 999.

B.

More than one realm can be assigned to a network interface.

C.

By configuring the hip-ip-list and icmp-address parameters, you enable the Net-Net 4000 network processor to respond to PING.

D.

Network interfaces define a subnet of useable addresses, not necessarily the address that signaling and media has to be directed to.

Which two of the following statements about H.323 on the Net-Net 4000 are TRUE?

A.

When functioning as a back-to-back gateway, the Net-Net 4000 appears as just one H.323 gateway to a single network.

B.

The Net-Net 4000 supports H.323 versions 1-6.

C.

Multiple virtual gateways or gatekeepers can exist on a single Net-Net 4000.

D.

There is a feature that allows an H.323 terminal that is unable to support Fast Start to receive a Slow Start call from a Fast Start source through the Net-Net 4000.

To view an existing multiple instance element configuration you can go to the correct branch of the configuration tree and _______________.

A.

select the element and then issue the show command

B.

enter the name of the element and then issue the show command

C.

type show and select from the displayed list

D.

type show

Berpd manages switchovers between the active and standby Net-Net 4000, and exchanges____________.

A.

Media flows

B.

Signaling information

C.

Health state

D.

All of the above

Which two the following statements about access to the Net-Net 4000 file system are TRUE?

A.

The Net-Net 4000 supports SFTP.

B.

You change the Net-Net 4000 internal FTP passwords by changing the User and Superuser mode passwords.

C.

The SD OS has a built in mechanism to prevent file system corruption.

D.

You should FTP software to the /code directory of the Net-Net 4000 flash memory when booting from /tffs0.

Which two of the following statements regarding SIP processing are FALSE?

A.

An initial INVITE will contain a From header tag and a To header tag as a globally unique identifier for the dialog.

B.

To avoid retransmissions, User Agents must forward received 100 Trying messages to their next hop.

C.

Calls Per Second are typically measured using a 7-10 message SIP call flow including call set-up and tear down.

D.

The combination of the To tag, From tag, and Call-ID completely defines a peer-to-peer SIP relationship and is referred to as a dialog.

Which two of the following statements about SIP response code handling on the Net-Net 4000 are TRUE?

A.

The Net-Net 4000 will originate a 403 Forbidden response when bandwidth allocated to a realm has been exhausted.

B.

The Net-Net 4000 cannot originate 3xx class redirect responses.

C.

The Net-Net 4000 egress realm selection may be affected by received third party 3xx class redirect responses

D.

The Net-Net 4000 can transmit a different SIP response code than it received.

In a(n) __________ exchange, a Master Slave Determination message is an example of a type of message that might be exchanged during the media setup portion of the call.

A.

RAS

B.

ISDN

C.

H.245

D.

H.225

Which one of the following statements about the Net-Net 4000 is TRUE?

A.

When the status LED, which is located on the front of the chassis control panel is lit yellow, it is an indication that the Net-Net system is experiencing a major malfunction such as a power supply failure.

B.

You can have up to two simultaneous console connections.

C.

By default, you can only Telnet to the wancom0 interface on the Net-Net 4000.

D.

By default, the Net-Net 4000 media interfaces will respond to PING.

If upon examination of two configuration files you notice that the version number of the permanently saved configuration differs from the version number of the running configuration, it means that __________.

A.

the saved configuration file has been edited, but the done command was not issued

B.

the saved configuration file has been copied from flash into SDRAM using the save-config command

C.

the saved configuration file has been saved into flash, but the activate-config command has not been issued

D.

the saved configuration file was copied from flash into SDRAM using the activate-config command