NFPA CFPS - Certified Fire Protection Specialist (CFPS)

OSHA regulation 1910.110 addresses storage and handling of liquefied petroleum gas (LPG). This regulation covers the general requirements for the design, construction, installation, operation, inspection, and maintenance of LPG systems, including containers, piping, valves, fittings, regulators, burners, and appliances. The regulation also specifies the safety precautions and procedures for the prevention of fire and explosion hazards involving LPG. The regulation applies to all employers who store, handle, or use LPG in their workplaces.References:

OSHA: 1910.110 - Storage and handling of liquefied petroleum gases1

Nebula Safety: Storage & Handling of Liquefied Petroleum Gases (LPGs)2

Class A roof coverings are the most effective in preventing the spread of fires from flying brands. Flying brands are burning embers or pieces of combustible material that are carried by the wind and can ignite other combustible materials or structures. Class A roof coverings are tested to withstand severe fire exposure from simulated fire sources, such as large burning brands, and do not produce flying brands themselves. Class A roof coverings include materials such as asphalt shingles, metal sheets, clay or concrete tiles, slate, and some types of synthetic membranes12. References:

Class A, B, and C Roof Ratings - UL

Fire-Resistant Roofs - Fire Safe Marin

Response Time Index (RTI) is a measure of thermal sensitivity of a sprinkler’s activation. It indicates how quickly the sprinkler responds to the heat from a fire. RTI is calculated by using the operating time, operating temperature, air temperature, air velocity, and conductivity factor of the sprinkler. RTI is independent of the gas velocity but depends on the properties of the sprinkler head such as mass, specific heat capacity and surface area of the thermal sensing element. RTI is used to classify sprinklers into fast response or standard response categories.

References:The Basics of Sprinkler Thermal Characteristics | NFPA;Sprinkler Characteristics According to NFPA 13 - Fire Protection …;Response time index (RTI) - Oil and Gas Drilling Glossary;RESPONSE TIME INDEX OF SPRINKLERS - Department of Building Environment …

The safety class for propane refrigerant R-290 is A3, which means it has no toxicity but high flammability. The safety class is determined by the ASHRAE Standard 34, which assigns a capital letter (A or B) for the toxicity level and a number (1, 2, or 3) for the flammability level of a refrigerant. Propane has a very low global warming potential and ozone depletion potential, but it also has a very low flash point and high auto ignition temperature, which make it highly flammable in the presence of ignition sources.References:Propane R-290 | Copeland US;R-290 Propane Refrigerant Fact & Info Sheet;Safety Data Sheet - Refrigerants; NFPA Fire Protection Handbook, 21st Edition, Chapter 3, Section 3.3.4.

Probabilistic fire models are categorized into network, statistical, simulation, and behavioral models. Network models use graph theory to represent the fire spread and the fire protection system in a building. Statistical models use historical data and probability distributions to estimate the likelihood and consequences of fire scenarios. Simulation models use mathematical equations and numerical methods to describe the physical and chemical processes of fire and its effects on the environment and the occupants. Behavioral models use psychological and sociological theories to predict the human response and evacuation behavior in case of fire. Network models are not a common category of probabilistic fire models, and they are not mentioned in the sources provided by the user. Therefore, network models are the correct answer.

References:Probabilistic Fire Simulation Assessment Using Simplified Model and Zone Modelling of a Kitchen Fire Scenario;Computer Fire Models for Fire Investigation and Reconstruction;Fire Behavior

A rate-of-rise heat detector is a type of heat detector that automatically resets after operation, when the ambient temperature drops below the operating temperature. This is because a rate-of-rise heat detector operates on a rapid rise in element temperature of 6.7° to 8.3°C (12° to 15°F) increase per minute, irrespective of the starting temperature1 If the temperature rise stops or reverses, the detector will reset itself and stop sending an alarm signal to the control panel2 A rate-of-rise heat detector can also have a fixed temperature element that will trigger an alarm at a specified temperature, but this element is not self-resetting and requires replacement after activation2

References:

Heat Detectors Selection Guide: Types, Features, Applications - GlobalSpec2

Heat detector - Wikipedia1

NFPA 484: Standard for Combustible Metals, 2020 Edition, provides requirements for the storage and handling of aluminum powders, flakes, and pastes. This standard covers the production, processing, finishing, handling, recycling, storage, and use of all metals and alloys that are in a form capable of combustion or explosion. It also covers operations where metal or metal alloys are subjected to processing or finishing operations that produce combustible powder or dust.NFPA 484 includes specific chapters for various metals and alloys, including aluminum and aluminum alloys12

References:

NFPA 484: Standard for Combustible Metals

NFPA 651: Standard for the Machining and Finishing of Aluminum and the …

Dipping and coating processes using flammable or combustible liquids pose a significant fire and explosion hazard and should be isolated from other operations, materials, or occupancies by location, fire walls, or operational procedures. Location refers to the physical separation of the process from other areas by distance or barriers. Fire walls are fire-resistance-rated assemblies that prevent the spread of fire from one side to the other. Operational procedures are rules or guidelines that regulate the conduct of the process and its personnel, such as limiting the amount of flammable or combustible liquids in use, controlling ignition sources, and providing adequate ventilation.

References: NFPA 34: Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids, 2021 Edition, Section 4.21; Fire Protection Handbook, 20th Edition, Volume 1, Chapter 8, Section 8.3.12.

1:NFPA 34: Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids2:Fire Protection Handbook, 20th Edition, Volume 1, Chapter 8

Cellulose nitrate products begin to decompose at about 300 °F (150 °C). This is the temperature at which the nitrate ester bonds start to break down and release nitric acid, which further catalyzes the decomposition. The decomposition temperature depends on the nitrogen content, the stabilizers, and the external heating rate of the cellulose nitrate. Higher nitrogen content, lower stabilizer concentration, and faster heating rate lower the decomposition temperature and increase the risk of thermal runaway.

References:Nitrocellulose - Wikipedia;Comparative analysis of stable decomposition and combustion kinetics of nitrated cellulose;Degradation of aged nitrocellulose investigated by thermal analysis methods;Nitrocellulose;Effect of stabilizers and nitrogen content on thermal properties of nitrocellulose

79% of fire departments surveyed participate in the delivery of emergency medical services (EMS).This is based on the NFPA report “US Fire Department Profile 2020”1, which states that nationwide, 37% of fire departments provided no EMS, 46% provided basic life support (BLS), and 17% provided advanced life support (ALS). Therefore, the percentage of fire departments that provided either BLS or ALS is 46% + 17% = 63%. However, this does not include fire departments that provided EMS through a third-party contract or agreement.According to the NFPA fire service survey from 2018–20202, 16% of fire departments reported having such an arrangement. Therefore, the percentage of fire departments that participated in the delivery of EMS in some form is 63% + 16% = 79%.References:

NFPA report - U.S.fire department profile3

US Fire Department Profile 2020 Supporting Tables2