CWNP CWNA-109 - Certified Wireless Network Administrator

CCI is still a possibility in this network because the client devices connected to one of the channel 1 APs will transmit frames that reach the other channel 1 AP as well as clients connected to the other channel 1 AP. CCI stands for co-channel interference, which is a type of interference that occurs when two or more devices transmit on the same channel within range of each other. CCI reduces performance and capacity because it causes contention and collisions on the wireless medium, which leads to retransmissions and delays. CCI can be mitigated by increasing physical separation between devices using the same channel or by reducing transmit power levels to limit coverage area. In this scenario, three access points are used within a facility. One access point is on channel 11 and the other two are on channel 1. The two access points using channel 1 are on either side of the access point using channel 11 and sufficiently apart so that they do not interfere with each other when they transmit frames. However, this does not prevent CCI from occurring between their client devices that are connected on channel 1. For example, if a client device connected to one of the channel 1 APs sends a frame to another device on the wired network or on another wireless network (such as an Internet server or a VoIP phone), that frame will be heard by both channel 1 APs as well as any other client devices connected to either of them on channel 1. This will cause CCI because these devices will have to wait for the channel to be clear before they can transmit their own frames. The answer that CCI only occurs in the 5 GHz frequency band is incorrect; CCI can occur in any frequency band where devices use the same channel. The answer that channel 11 loops around and causes CCI with channel 1 is also incorrect; channel 11 does not loop around and it operates in a different frequency band than channel 1. References: CWNA-109 Study Guide, Chapter 5: Radio Frequency Signal and Antenna Concepts, page 147

In wireless communication, several factors influence the effective reception of RF signals, including the receiving station's radio sensitivity, the transmitting station's output power, and free space path loss. However, the receiving station's output power does not influence the distance at which an RF signal can be effectively received. The key factors that impact signal reception distance are:

Receiving Station's Radio Sensitivity: This refers to the lowest signal strength at which the receiver can process a signal with an acceptable error rate. Higher sensitivity allows for better reception at greater distances.

Transmitting Station's Output Power: This is the power with which a transmitter sends out a signal. Higher output power can extend the range of transmission, making it easier for distant receivers to detect the signal.

Free Space Path Loss (FSPL): FSPL represents the attenuation of radio energy as it travels through free space. It increases with distance and frequency, reducing the signal strength as the distance from the transmitter increases.

The output power of the receiving station is related to how strong a signal it sends out, not how well it can receive or process incoming signals. Therefore, it does not affect the reception distance of incoming RF signals.

The string of characters and digits that is entered into an AP and a client STA for WPA2 security and is 8 characters long is called a passphrase. A passphrase is a human-readable text that is used to generate a Pre-Shared Key (PSK) for WPA2-Personal security. A passphrase can be between 8 and 63 characters long and can include any ASCII character. The PSK is a 256-bit key that is derived from the passphrase using a hashing algorithm called PBKDF2. The PSK is used to encrypt and decrypt the data frames between the AP and the client STA. A MSK is a Master Session Key that is generated by an authentication server for WPA2-Enterprise security. A WEP key is a 40-bit or 104-bit key that is used for Wired Equivalent Privacy (WEP) security, which is deprecated and insecure. A PSK is not a string of characters and digits, but a binary key. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 303; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 293.

The client drivers are faulty and should be upgraded is the likely problem for the laptop that can see and connect to 2.4 GHz APs, but does not even see 5 GHz APs. The client drivers are the software components that enable the wireless adapter of the laptop to communicate with the operating system and the network. The client drivers are responsible for scanning the available wireless channels, detecting and connecting to the access points, negotiating the security and data rate parameters, and transmitting and receiving data frames. If the client drivers are faulty, outdated, or incompatible, they may cause various issues with the wireless performance and functionality, such as low data rates, poor signal strength, frequent disconnections, or inability to see or connect to certain access points or channels.

One of the possible causes of faulty client drivers is that they do not support or recognize some of the features or standards of the 802.11ac technology, such as wider channel bandwidths, higher modulation schemes, or DFS (Dynamic Frequency Selection) channels. This could explain why the laptop can see and connect to 2.4 GHz APs, but not 5 GHz APs, as 802.11ac operates only in the 5 GHz band and uses channels that are wider (up to 160 MHz) and higher (up to channel 165) than those used by previous standards. Moreover, some of the 5 GHz channels are subject to DFS rules, which require the access points and client stations to monitor and avoid using channels that are occupied by radar systems or other primary users. If the client drivers do not support or comply with DFS rules, they may not be able to see or connect to access points that use DFS channels.

To solve this problem, the client drivers should be upgraded to the latest version that supports and is compatible with 802.11ac features and standards. This can be done by downloading and installing the updated driver software from the manufacturer’s website or using a device manager tool. Upgrading the client drivers may also improve other aspects of wireless performance and functionality, such as data rates, signal strength, security, and stability. References: 1, Chapter 12, page 493; 2, Section 8.1

Authenticated and Unassociated. According to one of the web search results1, a STA can be authenticated to multiple APs, but it can only be associated to one AP at a time. Association is the process of establishing a logical link between the STA and the AP, which allows the STA to send and receive data frames through the AP2. Therefore, when a STA has authenticated to an AP-1, but still maintains a connection with another AP-2, it means that the STA is authenticated to both APs, but only associated to AP-2. The state of the STA on AP-1 is authenticated and unassociated, which means that the STA can switch to AP-1 without repeating the authentication process, but it cannot send or receive data frames through AP-1 until it becomes associated.

The device in the bridge implementation that acts as the 802.1X Authenticator is the root bridge. The root bridge is the bridge that connects to the wired network and acts as the central point for all other bridges in the point-to-multipoint topology. The root bridge authenticates the non-root bridges using 802.1X/EAP and forwards their authentication requests to the RADIUS server. The non-root bridges act as the 802.1X Supplicants and use EAP methods such as EAP-TLS or EAP-PEAP to authenticate with the root bridge. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 459; [Cisco Aironet Wireless Bridges FAQ], question 29.

OFDM (Orthogonal Frequency Division Multiplexing) is the physical layer specification (PHY) that VHT capable devices must be backward compatible with according to the IEEE 802.11-2012 standard. VHT (Very High Throughput) is a PHY and MAC enhancement that is defined in the IEEE 802.11ac amendment and is also known as Wi-Fi 5. VHT operates only in the 5 GHz band and uses features such as wider channel bandwidths (up to 160 MHz), higher modulation schemes (up to 256-QAM), more spatial streams (up to eight), multi-user MIMO (MU-MIMO), beamforming, and VHT PHY and MAC enhancements. VHT can achieve data rates up to 6.9 Gbps.

According to the IEEE 802.11-2012 standard, VHT capable devices must be backward compatible with devices using OFDM PHY, which is defined in the IEEE 802.11a amendment and is also used by IEEE 802.11g, IEEE 802.11n, and IEEE 802.11h amendments. OFDM operates in both the 2.4 GHz and 5 GHz bands and uses features such as subcarriers, symbols, guard intervals, and OFDM PHY and MAC enhancements. OFDM can achieve data rates up to 54 Mbps.

Backward compatibility means that VHT capable devices can interoperate with OFDM devices on the same network by using common features and parameters that are supported by both PHYs. For example, VHT capable devices can use a channel bandwidth of 20 MHz, a modulation scheme of BPSK, QPSK, or 16-QAM, one spatial stream, no beamforming, and OFDM PHY and MAC headers when communicating with OFDM devices. Backward compatibility also means that VHT capable devices can fall back to OFDM mode when the signal quality or SNR is too low for VHT mode. References: 1, Chapter 3, page 123; 2, Section 3.2