Huawei H19-404_V1.0 - HCSE-Presales-Campus Network Planning and Design V1.0

Enabling the GRE checksum is optional. A functional point-to-point GRE tunnel requires a tunnel interface, GRE as the tunnel protocol, and reachable source and destination tunnel endpoints. The source identifies the local interface or IP address used to construct the delivery header, while the destination identifies the remote GRE endpoint. Without these endpoint parameters, the device cannot correctly encapsulate and deliver packets to the peer.

The checksum field is controlled by the Checksum Present bit in the GRE header. When checksum processing is enabled, the sender includes a checksum covering the GRE header and payload, and the receiver verifies it. This can provide additional corruption detection, but it increases processing and is not required for basic GRE operation. RFC 2784 explicitly labels the checksum field as optional and states that it is present only when the Checksum Present bit is set.

Huawei SD-WAN uses GRE or GRE over IPsec to establish data channels between edge devices. The essential tunnel and transport-network information is distributed through the control system, while optional GRE functions such as checksum validation may be enabled according to operational requirements.

==================

A network serving 15,000 wireless terminals is a large-scale WLAN and should use a standalone WAC solution. A dedicated WAC provides independent controller resources, scalable AP and user management, centralized WLAN policy control, and the ability to deploy controller redundancy without tying wireless-control capacity directly to a specific core-switch service card.

Huawei recommends a standalone WAC when the wireless network scale is large or when the wireless network is deployed independently over an existing wired campus. The WAC is typically connected to the aggregation or core layer in off-path mode, and VRRP hot standby can be used to improve reliability.

Native WAC solutions are valuable for unified wired and wireless management, authentication, forwarding, and policy enforcement. However, for a very large number of wireless terminals, the controller platform must be selected according to user, AP, traffic, and forwarding-capacity specifications. A standalone WAC allows the wireless control plane to be sized and expanded independently.

Option C provides the dedicated WAC together with the required core and aggregation or access infrastructure. Therefore, it is the recommended architecture for 15,000 wireless terminals.

The Network Management System is not an element of the IFIT measurement model. An IFIT measurement definition identifies the traffic to be measured, the locations where measurement actions occur, and the direction in which the flow is evaluated. The measurement flow specifies the target packets, usually through flow-identification fields. Measurement points define where packets are marked, counted, timestamped, or reported, such as ingress, transit, and egress nodes. Measurement direction distinguishes forward and reverse monitoring so that packet loss, delay, and path behavior can be analyzed correctly for each direction.

An NMS or controller remains operationally important because it creates measurement tasks, distributes configurations, receives telemetry data, correlates the results, and presents fault-location information. However, it is the management and analysis system surrounding the measurement model, not one of the model’s constituent measurement parameters.

Huawei positions IFIT as a high-precision telemetry mechanism used to delimit and locate application-quality faults. The training material highlights IFIT’s capability to locate faults rapidly and detect packet loss with extremely high reliability. Therefore, the component that is not part of the measurement model is the NMS.

==================

All four options represent objectives of a next-generation advanced industrial network. IP-based connections establish a standardized communications foundation, allowing production systems, controllers, sensors, machines, and management platforms to communicate through scalable Ethernet and IP technologies instead of isolated proprietary field networks.

Networked devices extend connectivity across operational technology assets so that equipment status, production data, and control information can be shared across production lines, plants, data centers, and cloud platforms. Network intelligence introduces automated provisioning, telemetry, analytics, fault prediction, policy optimization, and closed-loop operations. These capabilities reduce manual configuration and improve production availability.

Network-security integration is equally essential because greater openness and interconnection increase the potential attack surface. Security must therefore be integrated into access control, segmentation, device identification, encrypted communication, anomaly detection, and policy enforcement rather than added as an isolated external system. Huawei’s broader CloudCampus architecture similarly emphasizes automated provisioning, intelligent O & M, secure interconnection, integrated wired and wireless management, and open network capabilities. The four objectives collectively create an open, connected, intelligent, and secure industrial communications architecture.

==================

An AP’s transmit power must be maintained within an appropriate range. Excessive power does not automatically improve service quality. A high-power AP can enlarge its interference domain, create co-channel or adjacent-channel interference, produce asymmetric uplink and downlink coverage, and cause sticky-client behavior because a station continues hearing an AP even when its weaker transmission cannot reliably reach that AP. Huawei states that high-power APs can interfere with adjacent APs and that radio calibration dynamically adjusts AP channels, power, and frequency bands to ensure coverage while minimizing interference.

Conversely, power that is too low creates coverage holes, weak received signal strength, low modulation rates, retransmissions, and roaming instability. When a new AP is added, neighboring APs may reduce their transmit power to limit interference. When an AP goes offline, neighboring APs may increase power to compensate for the missing coverage. The engineering objective is therefore neither maximum nor minimum power, but sufficient coverage with controlled overlap and minimum interference. Accordingly, option B is correct.

==================

The statement is false because Huawei SD-WAN supports both priority-based link selection and load balancing. Multiple Internet or WAN links do not have to be treated equally. An administrator can define a preferred or primary link and designate another link as secondary or backup according to application requirements, link quality, cost, bandwidth, or operational policy.

For delay- and packet-loss-sensitive services such as voice and video, a higher-quality link can be configured as the primary path and another link as the backup. If the primary link no longer satisfies the configured SLA thresholds, traffic can be dynamically switched to a better path. Huawei’s material explicitly describes primary and secondary link selection based on SLA and also presents load-balancing-based steering as a separate option.

Load balancing is useful when an enterprise wants to utilize the bandwidth of multiple links concurrently. Priority-based active/standby forwarding is preferable when one provider offers better quality or when one circuit should be reserved for critical services. Intelligent traffic steering can additionally consider application priority and current bandwidth utilization. Therefore, multiple links can be prioritized, load-balanced, or used in a policy-controlled combination, making option B correct.

==================

The statement is true as a WLAN design recommendation. Inter-WAC roaming is supported, but it introduces more control-plane interaction and forwarding complexity than intra-WAC roaming. The Home WAC and Foreign WAC must belong to the same mobility group, synchronize station and AP information, and establish an inter-WAC CAPWAP tunnel for control information and, in some scenarios, service forwarding.

Additional synchronization, tunnel processing, route handling, and failure dependencies can increase roaming delay and complicate troubleshooting. This is especially relevant for delay-sensitive applications such as voice, video, automated guided vehicles, and real-time production systems. A better design places APs between which users frequently move under the same WAC wherever controller capacity and physical topology permit.

Avoiding inter-WAC roaming does not mean disabling the function entirely. Large campuses may require multiple WACs for scale, redundancy, or geographic distribution. Mobility groups should still be configured for unavoidable cross-controller movement. However, buildings, floors, and continuous roaming areas should be assigned carefully so that normal roaming remains intra-WAC. Therefore, the recommendation in the statement is correct, and the answer is True.

==================

All four options can be used as conditions by the iMaster NCE-Campus intelligent policy engine. Huawei describes this capability through a 5W1H-based policy model. “Who” represents the user identity, user group, or role. “Where” represents the access location, including the site, region, device group, device, SSID, or IP address. “How” represents the access mode, such as wired or wireless access and the authentication method used. “What” represents the terminal type or device attributes, including PCs and mobile operating systems.

The platform can combine these conditions rather than evaluating them independently. For example, a finance employee using a corporate laptop through wired 802.1X access at headquarters can receive different permissions from the same employee connecting through a personal mobile device at a branch. The authorization result can include a VLAN, ACL, security group, bandwidth limit, DSCP value, application policy, or URL-filtering rule.

This multidimensional evaluation enables context-aware, fine-grained access control. Therefore, A, B, C, and D are all correct.

==================

The statement is true. The AirEngine 8771-X1T uses dynamic-zoom smart-antenna technology that can adapt its radiation characteristics according to the deployment environment. In omnidirectional mode, the antenna pattern is optimized to provide broad and balanced coverage, making it appropriate for ordinary offices, corridors, classrooms, and other environments where users are distributed over a relatively large area.

In high-density mode, the antenna pattern is adjusted to concentrate radio energy more effectively within the intended service area. This reduces unnecessary signal leakage, limits interference between neighboring APs, and improves concurrent-user performance in lecture halls, conference rooms, auditoriums, and similar high-density environments.

The switching capability is more effective than using a permanently fixed antenna pattern because WLAN conditions can change as users move and traffic density increases or decreases. Huawei’s training material states that dynamic-zoom smart antennas dynamically switch between omnidirectional and high-density modes, improving coverage in omnidirectional mode while strengthening the user experience in high-density scenarios. Therefore, option A is correct.

==================