ARDMS SPI - Sonography Principles and Instrumentation

A wall filter in Doppler ultrasound is designed to remove low-frequency signals that are often caused by tissue motion, vessel wall movement, or other forms of motion artifact. These low-frequency signals can clutter the Doppler spectrum, making it difficult to accurately interpret blood flow velocities. By filtering out these unwanted low-frequency signals, the wall filter helps to enhance the clarity of the Doppler signal, allowing for more accurate measurements of blood flow velocities.

American Registry for Diagnostic Medical Sonography (ARDMS). Sonography Principles and Instrumentation (SPI) Examination Review Guide.

Comprehensive and Detailed Explanation From Exact Extract:

The matching layer is placed between the transducer’s piezoelectric element and the patient’s skin. Its primary function is to improve the transmission of sound energy into the body by reducing the acoustic impedance mismatch between the crystal and tissue, minimizing reflection at the transducer surface.

According to sonography instrumentation reference:

“The matching layer improves transmission of ultrasound energy by reducing impedance mismatch between the transducer and soft tissue, thus increasing the efficiency of sound energy transfer.”

Therefore, the correct answer is D: Increase sound transmission.

—

Lateral resolution refers to the ability of the ultrasound system to distinguish two structures that are side by side, perpendicular to the direction of the sound beam. This resolution is primarily improved by reducing the beamwidth. A narrower beamwidth allows for better differentiation between adjacent structures, enhancing the lateral resolution. Higher frequency transducers can also help achieve a narrower beamwidth, but beamwidth is the primary factor.

Comprehensive and Detailed Explanation From Exact Extract:

When evaluating high blood velocities, especially at angles closer to zero degrees (which produces maximum Doppler shifts), aliasing can easily occur because the Doppler frequency shift increases. To avoid aliasing, you must increase the Doppler scale (which increases the pulse repetition frequency, PRF) to accommodate these higher velocities.

According to sonography instrumentation references:

“The Doppler scale (PRF) must be increased when high velocities are anticipated to prevent aliasing, especially at optimal Doppler angles near zero degrees where maximum frequency shifts occur.”

Therefore, the correct answer is C: Increased Doppler scale settings.

—

Comprehensive and Detailed Explanation From Exact Extract:

A weakly attenuating structure allows ultrasound waves to pass through with minimal loss of energy. Because of this, structures located posterior to the weakly attenuating region appear brighter than expected — this is known as distal (posterior) enhancement. This artifact is most commonly observed when scanning fluid-filled structures such as cysts, the bladder, or the gallbladder.

Official sonography instrumentation reference states:

“When sound waves encounter a structure that attenuates sound minimally (low attenuation), more sound energy reaches deeper tissues. This results in increased echo amplitude from structures located distal to the weak attenuating structure, creating the appearance of distal enhancement.”

Therefore, the correct answer is D: Distal enhancement.

—

Comprehensive and Detailed Explanation From Exact Extract:

When the ultrasound beam travels through a structure that attenuates less than surrounding tissues, more energy reaches structures located deeper. This results in stronger echo signals from those deeper structures, which is visualized as a brightening or enhancement distal to the structure. This is referred to as acoustic enhancement or posterior enhancement.

Official sonography instrumentation reference states:

“Enhancement occurs as a result of reduced attenuation of the sound beam as it passes through fluid-filled or weakly attenuating structures, causing reflectors distal to the structure to appear more echogenic than normal.”

Therefore, the correct answer is B: Enhancement.

Autoclaving involves high-pressure steam at high temperatures, which can damage the delicate piezoelectric crystals within the ultrasound transducer. These crystals are responsible for converting electrical energy into sound waves and vice versa. Exposure to the extreme conditions of an autoclave can cause thermal and mechanical damage to the crystals, rendering the transducer ineffective.

ARDMS Sonography Principles and Instrumentation guidelines

Zagzebski, J. A. (1996). Essentials of Ultrasound Physics.

The intensity of an ultrasound beam is measured using a hydrophone. A hydrophone is a specialized device that detects and measures the acoustic pressure of the ultrasound waves in water or tissue-mimicking materials. It is highly sensitive and can measure the variations in pressure, which are used to calculate the intensity and other acoustic parameters of the ultrasound beam.

ARDMS Sonography Principles and Instrumentation guidelines

Hoskins, P. R., Thrush, A., Martin, K., & Whittingham, T. A. (2010). Diagnostic Ultrasound: Physics and Equipment.

The quality factor (Q-factor) is a dimensionless parameter that describes the efficiency of the transducer in terms of bandwidth and operating frequency. It is defined as the ratio of the operating frequency to the bandwidth. A higher Q-factor indicates a narrower bandwidth relative to the operating frequency, resulting in more precise frequency characteristics but potentially reduced axial resolution. Conversely, a lower Q-factor indicates a broader bandwidth, which improves axial resolution but may result in less precise frequency characteristics.